IMCOR 3.75 AND 5.00MM EXTERNALLY HEXED, SELF TAPPING HA COATED SCREW IMPLANTS WITH COVER SCREW

{0}------------------------------------------------ Image /page/0/Picture/1 description: The image shows the logo for the U.S. Department of Health & Human Services. The logo consists of a stylized caduceus symbol, which is a staff with two snakes coiled around it, and the words "DEPARTMENT OF HEALTH & HUMAN SERVICES - USA" arranged in a circular fashion around the symbol. The logo is black and white. Food and Drug Administration 9200 Corporate Boulevard Rockville MD 20850 JAN 30 1998 IMCOR™ C/O Robert S. Ura, DDS 5763 Long Brake Circle Edina, Minnesota 55439 Re: K974126 IMCOR™ 3.75 and 5.00mm Externally Hexed, Trade Name: Self-Tapping HA Coated Screw Implants with Cover Screw Regulatory Class: III Product Code: DZE Dated: October 13, 1997 November 3, 1997 Received: Dear Dr. Ura: We have reviewed your Section 510 (k) notification of intent to market the device referenced above and we have determined the device is substantially equivalent (for the indications for use stated in the enclosure) to devices marketed in interstate commerce prior to May 28, 1976, the enactment date of the Medical Device Amendments, or to devices that have been reclassified in accordance with the provisions of the Federal Food, Drug, and Cosmetic Act (Act). You may, therefore, market the device, subject to the general controls provisions The general controls provisions of the Act of the Act. include requirements for annual reqistration, listing of devices, good manufacturing practice, labeling, and prohibitions against misbranding and adulteration. If your device is classified (see above) into either class II (Special Controls) or class III (Premarket Approval), it may be subject to such additional controls. Existing major regulations affecting your device can be found in the Code of Federal Requlations, Title 21, Parts 800 to 895. A substantially equivalent determination assumes compliance with the current Good Manufacturing Practice requirement, as set forth in the Quality System Regulation (QS) for Medical Devices: General regulation (21 CFR Part 820) and that, through periodic (QS) inspections, the Food and Druq Administration (FDA) will verify such assumptions. Failure to comply with the GMP regulation may result in regulatory In addition, FDA may publish further announcements action. concerning your device in the Federal Register. Please note: this response to your premarket notification submission does not affect any obligation you might have under sections 531 {1}------------------------------------------------ Page 2 - Dr. Ura through 542 of the Act for devices under the Electronic Product Radiation Control provisions, or other Federal laws or requlations. This letter will allow you to beqin marketing your device as described in your 510(k) premarket notification. The FDA finding of substantial equivalence of your device to a legally marketed predicate device results in a classification for your device and thus, permits your device to proceed to the market. If you desire specific advice for your device on our labeling regulation (21 CFR Part 801 and additionally 809.10 for in vitro diagnostic devices), please contact the Office of Compliance at (301) 594-4618. Additionally, for questions on the promotion and advertising of your device, please contact the Office of Compliance at (301) 594-4639. Also, please note the regulation entitled, "Misbranding by reference to Other general information on your responsibilities under the Act may be obtained from the Division of Small Manufacturers Assistance at its toll-free number (800) 638-2041 or (301) 443-6597 or at its internet address "http://www.fda.gov/cdrh/dsmamain.html". Sincerely yours, Alilathrel thy A. Ulatows Timo Director Division of Dental, Infection Control and General Hospital Devices Office of Device Evaluation Center for Devices and Radiological Health Enclosure {2}------------------------------------------------ 510(k) Number (if known): N/A IMCCIR HA Coated Dental Implant Device Name: ## Indications For Use: IMCOR implan s are indicated to replace missing tooth roots for single tooth, partial and fully edentulous parients. The cover screw is used to protect the top of the implant and the internal threads during the healing process. The IMCOR In blant System is designed to become an osseointegrated prostheses allowing the attachment of partial or complete prosthodontic appliances. The use of the IMCOR implant is the same as currently accepted uses for dental implants already in the marketplace. All component: are to be used as labeled. Components are not intended to be bent, cast or altered by the clinician. ## (PLEASE DO NOT WRITE BELOW THIS LINE -CONTINUE ON ANOTHER PAGE IF NEEDED) ## Concurrence of CDRH, Office of Device Evaluation (ODE) Suen Rumm (Division Sign-Off) Division of Dental, Info and General Hospi 510(k) Number Prescription Use _ OR Over-The-Counter Use (Per 21 CFR 801-109) (Optional Format 1-2-96)